AHeatizon Systems After Installation Element Test.@ Heatizon
(Note: Cold leads are the Number 2 wires extending from the heating element to the transformer).
AAfter Installation Element Test@ form be completely filled out and that the form be signed
Heatizon Systems Floorizwarm Installation Manual
installation and witnessed by a representative of the party which contracted for the installation. It is essential that
covering, roofing material, concrete, etc. The Second Element Test is to be conducted following the covering of
Systems Element Tester (Part Number NI113). It is important that the same source be used to energize the Z
the heating element and immediately prior to installing the Control Box. The third Element Test should be
Lead.
5. Using an Amp meter, read the amperage (Amps) and Voltage (Volts) and record them on the form titled
6. Read and record the temperature of the area where the heating element is located.
Note: When using the Control Box and Transformer provided as part of your Heatizon product to
by both the party completing the test and the party witnessing the test.
3. Plug the Element Tester power cord into a 120 VAC power source.
Heatizon Systems After Installation Element Test
Attached please find three forms titled
conducted immediately following the energizing of the system. All of these tests may be conducted by using either
Leads and the welding cable lead from the Element Tester. Amperage can be read anywhere along either Cold
conduct the
Cold Leads will eventually connect to the transformer.
three different occasions. The First Element Test should be conducted immediately after the Cold Lead and Z
Part Number NI113
Mesh, Tuff Cable, or Floorizwarm Heating Element has been installed and before it has been covered up with floor
titled Calculation of Element Length, the length of the heating element can be calculated or verified.
different, a problem may exist. Do not energize your Heatizon Systems product, and call Heatizon
Aon@ position.
the Control Box and Transformer provided as part of your Heatizon Systems Product, or by using Heatizon
systems Technical Support at (801) 293-1232 to discuss the options available.
same. (Note: At the point where the readings remain the same, the temperature of the element should be
the Cold Leads will eventually connect to the transformer.
the heating element. In addition the results of these tests may help you in any troubleshooting that must be
4. Turn the Tester to the
Warning: In the event any of the measurements taken during the three After Installation Element Tests are
stabilized.)
Conducting these tests will help insure that a third party or an unknown event has not adversely impacted
performed on the system(s).
1. Connect one of the welding cable leads from the Element Tester to one of the Cold Leads near the point where
following steps 4 through 7 above.
installed per this manual. Once installation is complete, conduct three Element Tests by
Element Tester Instructions
It is Heatizon Systems recommendation that each test be completed by the party responsible for the
Systems recommends that the measurements be taken and the attached forms be completed on all zones on
Mesh, Tuff Cable and Floorizwarm Heating Element for all tests taken.
7. Using the numbers recorded on the form titled Heatizon Systems after Installation Element Test and the form
5. Continue taking the amperage and voltage readings every five (5) minutes or until the readings remain the
AHeatizon Systems After Installation Element Test.@ The voltage is to be read at the connection of one of the Cold
WARNING: Danger of Fire. This test will not detect cuts in Z Mesh, Tuff Cable, or Floorizwarm Heating Element.
all of the blanks on each
Page -ET1-
2. Connect the other welding cable lead from the Element Tester to the other Cold Lead near the point where the
AHeatizon Systems After Installation ElementTests,@ the entire product must be
<< < [Pag.19] > >>
Esta version es la html del arhivo pdf Floorizwarm_Install_Manual, genearada por domotica.name desde www.warmzone.com
Archivos relacionados:BlueHeat-Ins ComfortTileM DMC-IOM-Orig ECO-heater-b ETI-GIT-3A ETI-GIT-4 ETI-LCG-1 ETI-LCG ETI-LCR GXmanual_Jan LXCableInsta LXDatasheet NAGX-Ins-A-O OJ-ThermUser OJnon-progra RetroHeat-In System_Appli ThermalBoard Tile-Heat-Th february08_w march_newsle quicknet_spe quickstat_io roofheatinst tile-heating actuadores activethermal airwaysystem automatedceilingregisters coolcomponents easywarmfloor heatizon numinus pcslighting relampit taiserver temperatureguard touchplate warmzone
