(101.6mm)
· One (1) ETI P/N 12119 Machine Screw, #10-32 x 5/8".
2.1 Position sensor in the low end of gutter
Ambient Air
· One (1) ETI P/N 21207 Accessory Kit including:
Grid
For technical help, questions or comments concerning this product or any
Mounting Clamp
110.3B, Article 210.8(A)(3), Article 250.4(A), Article 426.4 & 28, Article 725.55 and
Model LCG 1
Make certain all conduit, cable, wire and terminations are approved for
Conduit Entry
4.00"
Ground
Nut
The ETI logo, We Manage Heat and Snow Switch are registered trademarks of Environmental Technology, Inc.
Read and follow all manufacturer's instructions for the safe and correct
unobtrusive location such as under the roof eaves.
Gutter Deicing Controller
BLACK
O-ring
as it was received.
· Two (2) ETI P/N 12905 Machine Screw Nuts, 5/16", #10-32.
0.20" (5.08mm) DIA 4 Places
Environmental Technology, Inc. product contact:
shock and fire hazard. Suitable ground fault detection and interrupting systems must be
YELLOW
YELLOW
Moisture
· One (1) ETI P/N 21209 Installation Sheet.
(UTC minus five hours).
Part Number 21206
Any installation involving electric heater wiring must be grounded to earth to protect against
current.
Sensing
established. If the unit must be returned, take care to ensure that it is packed
outdoor wet locations.
into the flow of melt water runoff (upstream)
Energize the snow melting system. Use care. Lethal
supplied).
Ammeter should indicate 0 amps.
Mount the housing securely in an upright position in a protected,
Email: helpdesk@networketi.com
3. A can of freeze spray or a 10 lb. bag of ice.
120V
2
Post-installation Test
1. Clamp the ammeter to either yellow lead within the enclosure.
Drill 3/16"Hole
depending on ambient air temperature.
www.networketi.com · helpdesk@networketi.com
· Three (3) ETI P/N 18703 Red Wire Nuts.
Packing List
Rigid Conduit
and specifically disclaims any implied warranties of merchantability or fitness for any particular purpose. Environmental Technology, Inc. reserves the right to revise
Sensing Grid
YELLOW
Environmental Technology, Inc.
organization of such revisions, changes or improvements.
PN 21209 Rev.B 08/2004
YELLOW
Questions & Comments
Fax: (888)234-4238 USA & Canada or
(574)233-1202 · Fax (574)233-2152
BLACK
Install Sensor
clamp and gasketed machine screw and nut
Installation Sheet
DISCLAIMER
Ambient Air
Temperature
The LCG1 is rated for 16 Amp heater loads at 120 VAC. The size
Environmental Technology, Inc. makes no representations or warranties, either expressed or implied, with respect to the contents of this publication or the products that it describes,
3. Cool temperature sensor to below 35°F (2°C) with ice or freeze spray.
within 1/4" of the gutter bottom. Mount the
Ground
MOST PROBLEMS RESULT FROM INSTALLATION ERRORS. BEFORE TESTING, VERIFY THAT
Sensor
Mount the moisture sensing grid near the heater cable.
WHITE
Screw
INSTALL PER ALL APPLICABLE ELECTRICAL AND BUILDING CODES AND REGULATIONS.
(101.6mm)
Unpacking
Sensor
this publication and to make changes and improvements to the products described in this publication without the obligation of Environmental Technology, Inc. to notify any person or
Temperature
of the branch circuit breaker must be 20 Amps or less. Refer to the
Equipment
3
Mount Housing
50/60Hz
Supply
Only qualified personnel trained in electrical equipment service should perform
120Vac
120 Vac
1. Clamp-on AC ammeter.
Toll Free (800)234-4239 · Fax (888)234-4238
Electric wiring to heating elements must be installed in accordance with Article
Moisture
(574)233-2152 elsewhere
4.00"
3/4" (21mm)
Jam Nut
Heaters
sensor. A separation of 1/2" (1.3cm) to 1"
Equipment Required
all other applicable sections of the National Electric Code (NFPA 70), local electrical
(2.5cm) is ideal.
(supplied) or through gutter to fascia using
Customer Service 8:00 a.m. - 5:00 p.m. EST
2.2 Fasten Sensor to gutter using mounting
3/4" (20mm)
Web: http://www.networketi.com
Hole Spacing
(574)233-1202 elsewhere
shipping container and related materials until normal operation has been
© 2004 Environmental Technology, Inc. All Rights Reserved.
4 9/16" (115.9mm) x 2 1/8" (54.0mm)
· One (1) ETI P/N 21206 LCG1 Gutter Deicing Controller.
WHITE
Nylon Clamp
1302 High Street · South Bend, IN 46601
heater cable close to but not touching the
Equipment
Sensor
Hazard of electrical shock. Follow all safety procedures.
mounting clamp and gasketed screw (not
voltages are now present within the control enclosure.
This may take some time, as long as one to two hours when using ice,
codes, and any third party standards.
2. AC voltmeter (optional).
Voice: (800)234-4239 USA & Canada or
Inspect the shipping container and packing material for damage. Save the
Heater & Circuit Wiring
4
in use at all times to reduce shock and fire hazard and to protect equipment.
Gutter
heater manufacturer's installation manual for additional branch circuit
®
to
WARNING
(near downspout) with moisture grid facing
Mounting Clamp
grid. Check ammeter. Ammeter should indicate the nominal heater
THE UNIT IS PROPERLY INSTALLED.
Customer Supplied
maintenance on heating and control equipment. Consult a licensed electrician.
HEATER
50/60Hz
2. Ensure the moisture sensing grid is clean and dry. Check the ammeter.
· One (1) ETI P/N 21206 Nylon Clamp, 1 3/8" ID.
1
We Manage Heat
· One (1) ETI P/N 20261 O-ring, 3/16" ID, 5/16" OD.
4. With temperature sensor below 35°F (2°C), wet the moisture sensor
requirements.
installation and operation of heater wire.
4.1 With an AC ammeter:
[Pag.1]
Esta version es la html del arhivo pdf ETI-LCG-1, genearada por domotica.name desde www.warmzone.com
Archivos relacionados:BlueHeat-Ins ComfortTileM DMC-IOM-Orig ECO-heater-b ETI-GIT-3A ETI-GIT-4 ETI-LCG ETI-LCR Floorizwarm_ GXmanual_Jan LXCableInsta LXDatasheet NAGX-Ins-A-O OJ-ThermUser OJnon-progra RetroHeat-In System_Appli ThermalBoard Tile-Heat-Th february08_w march_newsle quicknet_spe quickstat_io roofheatinst tile-heating actuadores activethermal airwaysystem automatedceilingregisters coolcomponents easywarmfloor heatizon numinus pcslighting relampit taiserver temperatureguard touchplate warmzone
