e ......7
unused trunk input of your phone system, access code disabled
attiio
such changes.
approximately two minutes, then hang up and repeat this sequence two more times. This sequence can be halted by
o rrtt L
4 5
Doorbox 3
Printed in the U.S.A.
nected to the RC-3, then enter the relay
c k
1-9
(W-2000A shown)
To force the RC-3 to hang-up (four beeps) .................................................................................................................
1 2 3 4 5 6 7 8 9 10
RJ-OUT
PABX/KSU
6 6
To activate a relay continuously (latch) ..........................................................................................................
8 6
G. Relay and Answer LED's
S u
VIKING©
RC-3's 12 digit (maximum) alarm dialing number, the RC-3 should not be placed behind a PABX
8 6
To start a timed activatation for all relays (two beeps) ................................................................................................
Doorbox 2
a x
RELAY 3
6 ..4
box, the person on the control phone sim-
err A
5 ..3
3
Due to the dynamic nature of the product design, the information contained in this document is subject to change without notice. Viking Electronics, and its affiliates and/or
D. RC-3 Commands
5
fourth LED is labeled ANSWER. This LED lights when the RC-3 has answered or seized the line and will flash during
BATTERY FEED
Doorbox 1
,123456 (two beeps) 2 1 (two beeps)
vating relays, two beeps after activating relays, three beeps after a "halt" command or incorrect entry (error), and four
beeps if 20 seconds have elapsed between Touch Tone commands or a forced hang-up command is entered.
plliic
ON
pp
ns
B a
Five seconds after the closure is made, the RC-3 will pulse dial (10 pps) the programmed number, hold the line for
To control the RC-3's operation, enter one of the following commands:
6
alarm dialing.
2. Starting the timed activation of Relay 3 locally, with the RC-3 on an
To halt and remove the last digit entry (three beeps) ..................................................................................................
12V TALK
3 4
OFF
To de-activate a latched relay ........................................................................................................................
u c
-
To disable the alarm dialing sequence and force the RC-3 to hang-up (four beeps) ...................................................
POWER 12 VDC
C. Relay Commands
E. Confirmation Beeps During Operation
5 ..3
7 1
Input of
The relay status LED's are labeled RELAY 1, RELAY 2, RELAY 3 and light whenever relays 1, 2 or 3 are closed. The
d u
ply has to access the trunk or station con-
01
12 VDC
MODEL RC-3
1
02
3. Remotely stop the RC-3 from calling you (three times if not
ALARM
To interrogate relay status (one beep = de-activated, two beeps = activated) ................................................
Unused
ZF300350 Rev D
L iin
Fax Back Doc 165
he
H. Operating Examples
3 2
#
2
Trunk
3 8
p p
1 5
k L
o d
ca
L iin
3 8
a c
e ......7
0
4 3
c tt S
one of the following commands:
The RC-3 can be used as an emergency dialer, activated by a continuous contact closure between terminals 8 & 9.
x B
Enter
reset or open between terminals 8 and 9 before initiating a second alarm dialing sequence. Note: The RC-3 will not
Otth
6 ..8
RELAY 1
Door Strike 1
F. Alarm Dialing (Loop start C.O./Centrex line and PABX station applications only)
Enter Digits
(W-2000A shown)
There are four types of beeps you will hear while controlling the RC-3. A single beep should be heard after de-acti-
VIKING©
u p
Call
To activate a relay momentarily (timed activation - factory set to 5 seconds)) ................................................
HUDSON,WI 54016
(two beeps)
n e
Description
The RC-3 can remotely control three door
8 6
Call
1-9
To use the RC-3's relay commands, enter the relay number (1-3 for a single unit or 1-9 for multiple units) then enter
VIKING©
initiate a alarm dialing sequence during user operation or programming. Therefore, a continuous contact closure is rec-
strikes from any station on your PABX.
on
F
RELAY 2
INPUT
p o
programmed to 123456 and enabled
VIKING©
Ap
(W-2000A shown)
3 RELAY REMOTE
TOUCH TONE CONTROLLER
1-9
F a
Enter
ELECTRONICS
activation code for that door strike.
P
O
ommended. Due to the
subsidiaries assume no responsibility for errors and omissions contained in this information. Revisions of this document or new editions of it may be issued to incorporate
7 1
+
Call
1. Relay 2 activating from a remote location with the access code
when long distance dialing is required.
After verbal confirmation from the door-
n e
(answer phone) # (four beeps) (hang up)
alarm is set (Terminals 8 & 9 are closed), indicating the alarm condition. The RC-3 requires a minimum of a 5 second
1 5
VIKING
6 6
P rro
Door Strike 3
Relay
entering a Touch Tone # locally or at the dialed location. The RC-3 will output a single beep every 5 seconds while the
Door Strike 2
1-9
RJ-IN
disabled) during an alarm sequence
s
#
<< < [Pag.4]
Esta version es la html del arhivo pdf rc-3, genearada por domotica.name desde www.vikingelectronics.com
Archivos relacionados:1900-series E-40 SL-1 SL aes-2000 c-1000b c-4000 cpa-7b cpc-1 cpc ctg-1 ctg dna-510 dva-2wa dva-3003 e-10-20a-ewp e-30 e-30-pt eram-60 es-1 es faxj-300 fbi-1a hd-1 hd hf-3w k-1900-4 lc-8 ldb-2 ldb-3 lla-4 lm-1a ls-4x4 m2w moh-2l mtg-10 pa_30 pan-1 pan pb-100 pi-150w privacy ps-2r rad-1a rg-10a so-24a ve-boxes ve-light seguridad cctvsafe extremecctv freezealarm goodbarsecurity highpowersecurity icontrol infosecinstitute intamac jacksonsystems keepsafer mraccess napcosecurity nexusaudiosystems securityandmore securitymaninc smartvue techno-mall tripplite vigitron vikingelectronics wilife
