B. Secured Access (DIP Switch 1 OFF)
6..8
erra
RELAY
orrtt L
#
6..4
38
1
OFF
assume no responsibility for errors and omissions contained in this information. Revisions of this document or new editions of it may be issued to incorporate such changes.
86
e......7
N.O.
86
- then - Enter Memory Location
66
Enables all DTMF (Touch Tone) detection (factory default)
#
6 digits
PHONE
OFF
VIKING© MODEL RAD-1A
# 7
N.C.
2
OFF
P
3
INE
71
C. DIP Switch Programming
When an access code has been programmed, the RAD-1A answers the inbound call and prompts the caller with a sin-
on
71
error. To begin programming, call the RAD-1A. When the RAD-1A answers, you have 20 seconds to enter
OUT
Silence time out (01 - 99 seconds) (factory disabled) ..................................................
2 digits
66
HUDSON, WI 54016
O
5..3
#45
12 3
No security code required to enter the programming mode
+ location number (45, 48, or 49) without any preceding numbers.
n
in which the RAD-1A is put into. Viking Electronics Inc. is not able to assume responsibility since it is a function of the
Enter Digits
Alert tones on (factory setting) .................................................................................
D. Programming and Remote Access Features (requires a Touch Tone phone)
ZF302160 Rev A
Set all programming features to factory settings .......................................................
7
4
86
15
OUT
up
Description
5..3
L
6
ucctt S
ON
pe
1
6
9
LEARN
Switch
Prro
e......7
then
(factory default)
43
acckk L
Access Code (6 digits, 0-9, no digits disables) (factory disabled) ................................
RELAY
access to the 600 Ohm input/output of one-way paging amplifiers, digital announcers and other audio programs.
LINE
IN
entire system assembled by the installer/owner. A Viking TR-1 Toll Restrictor may be added to help prevent toll abuse
OFF
5
(Do Not Use)
LINE
Disables all DTMF (Touch Tone) detection
#47
Liin
Due to the dynamic nature of the product design, the information contained in this document is subject to change without notice. Viking Electronics, and its affiliates and/or subsidiaries
If the access code has not been programmed, the unit is "Unsecured." In this mode, the RAD-1A answers the inbound
If a valid Touch Tone sequence is entered while programming, a double beep will be heard. Three beeps indicate an
followed
Important: It is crucial that the installer and system owner understands the functions and capabilities of both the RAD-
Fax Back Doc 410
then
45
then
possibilities are understood. This enables the installer and owner to make risk managing decisions about the system
Note: To disable or eliminate the use of any of the above features, enter the #
axx B
Security code required to enter the programming mode
6 digits
Ba
600
on
Quick Programming Features
Exit Programming and disconnect ...........................................................................
Normal Operation (factory default)
Su
F
by your 6 digit security code (a double beep should be heard). The RAD-1A may now be programmed. Note: While
od
PHONE
tems. The RAD-1A will answer an incoming call on the first ring. The RAD-1A offers either unsecured access, or secured
DEVICE
15
#48
Printed in the U.S.A.
pp
###
0
po
Alert tones off ...........................................................................................................
ON
5
COM
DTMF
seconds, the RAD-1A will triple beep and hang up. When a valid access code has been entered, the RAD-1A will dou-
if the PABX and RAD-1A toll restriction is not adequate.
OFF
ENABLE
123
ON
AUDIO
ble beep (if alert tones are ON) and bridge the line to the device connected to the RAD-1A's output.
38
3
Fa
ne
34
OHM
ne
attiio
call, double beeps (if alert tones are ON), and bridges the line to the device connected to the RAD-1A's output.
PHONE
ON
Call timer (0-1 hrs, 00-59 mins, 00-59 secs) (factory disabled, 3 sec minimum) .............
The RAD-1A allows remote access to any 600 ohm audio device. This can be very useful for remote access to paging sys-
Liin
5 digits
RELAY
4
2
12
MODE
gle beep. The caller is then required to enter a 6 digit access code. If the proper access code is not entered within 20
3
programming, if no Touch Tones are entered for 20 seconds, the RAD-1A will give 3 beeps and disconnect.
VIKING
ON
Security code (6 digits, 0-9) (factory set to 845464) .................................................
then
Position
#49
A. Unsecured Access
REMOTE ACCESS
1A and the lines and/or PABX stations connected to the RAD-1A, so that any and all toll fraud and other system abuse
du
ELECTRONICS
Op
<< < [Pag.4]
Esta version es la html del arhivo pdf rad-1a, genearada por domotica.name desde www.vikingelectronics.com
Archivos relacionados:1900-series E-40 SL-1 SL aes-2000 c-1000b c-4000 cpa-7b cpc-1 cpc ctg-1 ctg dna-510 dva-2wa dva-3003 e-10-20a-ewp e-30 e-30-pt eram-60 es-1 es faxj-300 fbi-1a hd-1 hd hf-3w k-1900-4 lc-8 ldb-2 ldb-3 lla-4 lm-1a ls-4x4 m2w moh-2l mtg-10 pa_30 pan-1 pan pb-100 pi-150w privacy ps-2r rc-3 rg-10a so-24a ve-boxes ve-light seguridad cctvsafe extremecctv freezealarm goodbarsecurity highpowersecurity icontrol infosecinstitute intamac jacksonsystems keepsafer mraccess napcosecurity nexusaudiosystems securityandmore securitymaninc smartvue techno-mall tripplite vigitron vikingelectronics wilife
