Enter (0-9), #, 2, 3 to program E & M timing for channel 3.
Due to the dynamic nature of the product design, the information contained in this document is subject to change without notice. Viking
Use DIP switches 1, 2, and 3 on the front panel to select Ring Trip Interface or E & M mode for channels 1, 2 and 3.
Enter 2 digits (01-99), #, 3, 2 to set the message repeat count for channel 2.
Enter (0-9), #, 1, 2 to program ring delay for channel 2.
SINGLE CHANNEL DIP switch to ON, then momentarily disconnect power.
ERAM-60 chip will add one minute of announcement memory. To enable the single channel mode, set front panel
Enter (0-9), #, 1, 1 to program ring delay for channel 1.
7. Transfer Phone Numbers
Note: To disable the hook switch flash transfer for a channel, leave the 16 digit
Enter up to 16 digits (1-9), #, 0, 3 to program a transfer phone number for channel 3.
6
8. Message Repeat
the C.P.C. signal (if present) and disconnect that line. It is now immediately ready for the next incoming call.
The Beginning Of Message and End Of Message pulse width is factory set to 600msec. This may be programmed
programmed from "Immediate Answer" (0) to 9 rings. Example: If ring delay is set to 1, unit will answer after one
DVA-3003 will perform a hook switch flash transfer (dialing the programmed phone number after the channel
Enter 2 digits (01-99), #, 3, 3 to set the message repeat count for channel 3.
The DVA-3003 may be configured as a single channel announcer with up to 12 minutes announcement time. In this mode
Each channel has the ability to repeat the announcement up to 99 times before disconnecting or transferring an
Enter 2 digits (01-99), #, 3, 1 to set the message repeat count for channel 1.
number. To change the security code, enter your 6 digits _ _ _ _ _ _ plus #,4,7.
5. Ring Delay (Ring Trip Interface)
9. Changing Your Security Code
Enter (0-9), #, 1, 3 to program ring delay for channel 3.
this document or new editions of it may be issued to incorporate such changes.
of operation, channels 2 and 3 are disabled, and channel 1 utilizes the combined digital announcement memory time of all
from 100msec. (enter 1) to 900msec. (enter 9) for each channel.
These switches are only read when first powered up. Momentarily disconnect power after changing the DIP switches.
Enter up to 16 digits (1-9), #, 0, 1 to program a transfer phone number for channel 1.
6. E & M Timing
The ring delay is factory set to "Immediate Answer" (unit answers in less than one full ring). The ring delay can be
field blank.
Printed in the U.S.A.
perform a hook switch flash transfer if a number is programmed, or disconnect. The BUSY screw terminals provide a
full ring cycle.
the PBX table on pages 4 and 5 for the control lead connections.
After the DVA-3003's announcements have been recorded and monitored, place the unit into the ANNOUNCE mode.
A standard C.O. line or PABX extension should be connected to the CO/PABX LINE input jack for that channel. The
ERAM-60 memory expansion chips can be installed to extend the announcement memory to a total of 12 minutes. Each
answered call. The factory default for the message repeat count is set to 01.
Note: The security code can not include a D or #.
Enter (0-9), #, 2, 2 to program E & M timing for channel 2.
Enter (0-9), #, 2, 1 to program E & M timing for channel 1.
Fax Back Doc # 127
A. Ring Trip Interface
Enter up to 16 digits (1-9), #, 0, 2 to program a transfer phone number for channel 2.
Fax Back Line...(715) 386-4345
The transfer phone numbers are disabled from the factory. When a transfer phone number is programmed, the
Product Support Line...(715) 386-8666
Enter (0-9), #, 1, 4 to program ring delay for programming port.
three channels. A stock DVA-3003 has a total of 3 minutes of single channel announcement memory. Viking model
contact closure during the announcement. If the caller hangs up during the announcement, the DVA-3003 will detect
Single Channel Mode
It is recommended that you change the security code from the "845464" factory setting to your own personal 6 digit
B. 4 Wire E & M Interface:
ZF300720 Rev C
Operation
The 600 OHM E & M jack provides a 600 ohm "Dry" output. Refer to the protocol timing specifications on page 3 and
Electronics, its affiliates and/or subsidiaries assume no responsibility for errors and/or omissions contained in this information. Revisions of
DVA-3003 will answer after the programmed ring delay, play the announcement for the message repeat count,
announcement has been played.
<< < [Pag.6]
Esta version es la html del arhivo pdf dva-3003, genearada por domotica.name desde www.vikingelectronics.com
Archivos relacionados:1900-series E-40 SL-1 SL aes-2000 c-1000b c-4000 cpa-7b cpc-1 cpc ctg-1 ctg dna-510 dva-2wa e-10-20a-ewp e-30 e-30-pt eram-60 es-1 es faxj-300 fbi-1a hd-1 hd hf-3w k-1900-4 lc-8 ldb-2 ldb-3 lla-4 lm-1a ls-4x4 m2w moh-2l mtg-10 pa_30 pan-1 pan pb-100 pi-150w privacy ps-2r rad-1a rc-3 rg-10a so-24a ve-boxes ve-light seguridad cctvsafe extremecctv freezealarm goodbarsecurity highpowersecurity icontrol infosecinstitute intamac jacksonsystems keepsafer mraccess napcosecurity nexusaudiosystems securityandmore securitymaninc smartvue techno-mall tripplite vigitron vikingelectronics wilife
