3 From the main menu press 1
d) Enter the time delay in minutes (i.e. 15 for 15 minutes,
programming this zone and return to step 1.b)
degrees, high is 90 degrees, low is 70 degrees, humidity is 50
6 You will hear "Enter Zone to Change"
b) Press 1 to make a change (Press 2 to return to the Set Limits
e) You will hear the value you just entered
Clearing High and Low Temperature / Humidity Values
9
1 Call the Computer Room Guard
c) You will hear "Enter number then press pound"
(Press 2 to skip and proceed to step 6.a or press 0 to stop
push-button down for at least 5 seconds while that sensors
2 Enter you PIN number
5 Press #
To access the Program Menu:
programming this zone and return to step 1.b)
c) Press 1 to change the limit
d) You will hear "Enter number then press pound"
humidity limit for that zone (i.e. 0 percent)
to change"
Checking Sensor Values Remotely
Clearing High and Low Values Locally
f) Proceed to step 1.b
Repeat the steps 1 to 6 for each connected sensor/zone.
menu)
3 From the main menu press 1
j) You will hear "Enter number then press pound"
1 Call the Computer Room Guard
f) Proceed to step 5.a
g) You will hear "Zone x upper humidity limit is" and the current
4 You will hear "Enter Zone"
e) You will hear the value you just entered
a) You will hear "Zone x lower humidity limit is" and the current low
6 You will hear the zone's sensor values and their highest and
4 You will hear "Enter Zone"
b) You will hear "Press 1 to change"
5. Programming the Lower and Upper Humidity Limits
in minutes.
high humidity limit for the selected zone (i.e. 100 percent)
reset.
e) Enter the value then press #. (Acceptable range 0% to 100%)
(Press 2 to skip and proceed to step 6.g or press 0 to stop
6 You will hear "Enter Zone to Change"
l) You will hear the value you just entered (i.e. 70 percent)
6. Programming the humidity callout delay time
m) Proceed to step 6.a
i) Press 1 to change the limit
a) You will hear "Humidity callout time delay is XX minutes, press 1
4 You will hear "Enter Zone"
high and low data is being displayed.
Example "Zone 1, server room number 1, temperature is 80
Remotely
acceptable range 0 to 900 minutes)
High and low values can be cleared by holding the black
d) Enter the time delay in minutes (i.e. 15 for 15 minutes,
Disconnecting a sensor
7 Enter the number of the zone whose sensor data you wish to
2 Enter you PIN number
3 From the main menu press 1
f) You will hear the value you just entered (i.e. 20 percent)
5 Press #
5 Enter the number of the sensor you wish to hear (i.e. 1)
16
percent, high is 95 percent, low is 22 percent."
1 Call the Computer Room Guard
lowest reading, and how long the sensor has been out of limits
emergency phone call, perform the following steps:
2 Enter you PIN number
To stop monitoring a particular sensor without causing an
k) Enter the value then press #. (Acceptable range 0% to 100%)
7 Remove the sensor you wish to stop using.
acceptable range is 0 to 900 minutes)
h) You will hear "Press 1 to change"
<< < [Pag.9] > >>
Esta version es la html del arhivo pdf computer_room_guard_manual_r6, genearada por domotica.name desde www.temperatureguard.com
Archivos relacionados:AN505E ANDCP-E DCP_Getting_ DCP_IP_Setup DCP_Manual_v DCP_manual IP_Setup_rev MA41201 MA412_Wiring MOLLY303_Wir MOLLY305_Wir NetworkAddre VM500-5_Inst VM500_INSTAL VM500_Mounti VM5032-2002 VM50522 VM505E_510Em VM52002 VaccineRepor ab305v aci-1k-2w-bp aci-1k-2w-sp ma401_wiring ma403 molly303_spe pump_sequenc rl-b_wiring_ vm500-5E-DCP vm500-6wirin vm501_manual vm501_specsh vm502_specsh vm504_manual vm505 vm50518 vm50520 vm5057r14 vm506_manual vm50811 vm508_specsh vm509 vm51001 vm510_specsh vm511_specsh vm54001 vm540lv_wiri actuadores activethermal airwaysystem automatedceilingregisters coolcomponents easywarmfloor heatizon numinus pcslighting relampit taiserver temperatureguard touchplate warmzone
