c) Press the Button. The selected source LED will slowly flash orange.
2. Point the RC-4 at the IR Port and press one of the four Source Buttons, (1-4) depending on which
b) Press the source button (1-4) for the bank that contains the command to be erased.
c) Press the Source Button (1-4) for the code bank to be erased. All learned IR commands for that
Programming utilizes the RC-4 Remote Control, the original manufacturer remotes for the sources to be
solid red will now begin to flash slowly in red. This indicates that the C-4.1 is ready to learn the play
put the C-4.1 into the Learn Mode.
(The play command will be placed under the source button and will be output every time the source
bank will be erased and the LEDs will flash green three times.
C-4.1 Installation Instructions
First Draft
source is to be programmed. After a Source has been selected, the LEDs will stop scrolling and the
flash green three times to indicate the command has been learned and then return to solid red. If the
connected to the WP4) needs to be programmed for Source IR commands.
9. If programming an expanded system with two C-4.1 Controllers, only the Master Controller (the one
1. To erase an entire source:
1. Activate Learn Mode by pointing the Nexus RC-4 Remote Control at the IR Port (Nexus Logo) on the
NOTE: The IR command for PWR for all sources is output automatically whenever the first zone in
program C-4.1 source control:
the system comes on, or after the last zone in the system is turned off.
controlled and requires that the C-4.1 Controller has AC power. The WP4 Remote Input Module and all
4. Point the source remote with the play command to be learned at the IR Port from a distance of 1 to 2
a) Point the RC-4 remote toward the C-4.1 IR Port and press the LRN Button for 5 seconds. This will
put the C-4.4 into the Learn Mode.
Step 2 until all source commands have been learned.
LEDs below the IR Port will scroll red from left to right. This indicates the C-4.1 is in Learn Mode and
d) Press the RC-4 function button (<<,*,>> or PWR) with the code to be erased. Any learned IR
a) Point the RC-4 remote toward the C-4.1 IR Port and press the LRN Button for 5 seconds. This will
20
2. To erase a single command:
4.1 will switch to that source rather than be ready to learn the play command. The LED that was lit
the source remote to program the corresponding IR commands.
8. Test all commands to confirm programming. Repeat previous steps for commands that do not
C-4.1 Top Panel and pressing the LRN Button for 5 seconds. Release the LRN Button. The four
selected source, by alternately pressing the <<,*,>> and PWR buttons on the RC-4 and then using
Erasing IR Commands
6. To program the IR commands for the other sources, repeat Steps 2-5 selecting a different source in
7. When all IR programming is complete, press the LRN Button on the RC-4 to exit Learn Mode.
sources should be connected and have IR emitters connected and attached to test commands. To
command.
press the source button pressed in Step 2 again to prepare the C-4.1 to learn the play command.
There are two methods to erase IR commands on the C-4.1. One is to erase an entire source the other is
ready for a Source to be selected.
3. If the component being programmed has a play command, (CD play, DVD play etc) on the RC-4,
to erase an individual command.
b) Press the Button. The four LEDs will scroll orange from left to right.
LED corresponding to the source selected will illuminate solid red.
5. Repeat the learning process for the other programmable buttons, (<<, * , >> and PWR) for the
button is pressed.) If a different source other than the one indicated by the lit LED is selected, the C-
inches. Quickly press and release the play button. The Source LED on the C-4.1 will flicker red, then
LED flashes red three times instead of green, repeat Steps 3-4.
function properly.
command for that button will be erased and the source LED will flash green three times.
<< < [Pag.20] > >>
Esta version es la html del arhivo pdf C-4-1InstallationInstruct, genearada por domotica.name desde www.nexusaudiosystems.com
Archivos relacionados:C-4-4Install C6OwnersManu CEDIAExhibit NexusBrochur NexusC4-4Bro NexusC4_1Bro NexusC4_4Bro NexusT-2Broc T2Installati ZED-2Manual seguridad cctvsafe extremecctv freezealarm goodbarsecurity highpowersecurity icontrol infosecinstitute intamac jacksonsystems keepsafer mraccess napcosecurity nexusaudiosystems securityandmore securitymaninc smartvue techno-mall tripplite vigitron vikingelectronics wilife
