When powering the adapter from a DC Power Source
Figure 2
Load regulation
Input voltage
to the device.
dissipate. Call us for alternate ways of connecting more than one device to your DC source.
Can I plug the computer in when it is running? Yes.
temperature may result.
Output Current Limit
Size
Figure 1
adapter. Do not cover or restrict airflow around adapter in any manner. Excessive adapter
immediately. Contact a Lind service representative.
AC power cord
Low Input Voltage Cut-Off (DC input only)
ˇ Do not damage, stretch, or excessively bend the power cord. A fire or electric shock may
5. Confirm that the green "Output Present" LED is on and that power is being supplied
DC Input
AC power cord to adapter
To connect the adapter to your system from a DC voltage source: (Reference: Figure 2)
This connection sequence may be altered without an effect on operation.
Connect output
When powering the adapter from an AC Power Source
Common Questions Concerning Power Adapters
Snap-in output cable to adapter
ˇ If you detect smoke or unusual smell, turn your device off and unplug the power plug
simultaneously. However, if this inadvertently happens neither the adapter nor your device will be
to DC source outlet
2. Plug the connector of the DC output cable into the mating DC input connector on the
Operating rel. humidity
-40ēC to +85ēC
Weight
has been activated. Also, check the fuse in the input power cable.
start back up.
start the vehicle with the adapter in place. Many jump start systems use high voltages that will
Ripple & noise
Output Short Circuit Protected
Does it matter which cable gets plugged in first? No.
1.5 amperes maximum
when plugged in, what is wrong? Some vehicles must be running or must have the key ON to
This connection sequence may be altered without an effect on operation.
1. Firmly plug the snap-in connector of the DC output cable into adapter output jack.
*Note: It is not recommended that the adapter be connected to an AC and DC voltage source
to AC source outlet
to the device from a DC source.
Operating ambient temp.**
or cover it with anything in such a way that heat can not dissipate.
damage the cord and consequently cause a fire or electric shock.
Indicators
5 - 95% non-condensing
hands are wet. An electric shock may result.
Output voltage
LED on adapter (Output power present)
Frequency
with lighter plug splitter cables. These devices can cause the cigarette lighter plug on the adapter
Storage temperature
ˇ The rated AC input voltage is between 90 VAC and 264 VAC. The input voltage need not be
short circuit or electric shock may result.
Output current
ˇ Never attempt to plug or unplug the power plug or the connector of the AC adapter when your
ˇ When unplugging the power plug, grasp the plug, not the cord. Pulling the cord forcibly can
Input voltage
Observe voltage polarity when wiring. (Black wire = ground)
LED on automobile plug if equipped (Input present)
Cautionary notes when using AC power
You can now use your system with the power supplied by the adapter.
Noted on input cable label.
Is it OK to start or stop the vehicle engine with the adapter plugged in? Yes, but do not jump
2. Plug the connector of the DC output cable into the mating DC input connector on the
operating in high ambient temperatures. Use caution when handling and mounting the
electronic device you are to power.
6.0 x 1.75 x 1.75 inche
ˇ The metal case of the adapter can get quite warm during normal use, particularly when
Can this adapter be used with a multi output cigarette plug splitter? Use extreme caution
2% maximum
to the adapter or your mobile device. Do not place the adapter in the vehicle glove compartment
Environmental
1. Firmly plug the snap-in connector of the DC output cable into adapter output jack.
Internal Overtemp Cut-Off (DC input only)
s
Input Fuse
electronic device you are to power.
DC Voltage Specifications
LED
circuitry. Starting the vehicle may turn the adapter off. After a ten second delay, the adapter will
cable to device
ˇ Never attempt to disassemble or modify the adapter.
4. Plug the outlet end of the AC power cord into your AC wall outlet.
3. Insert the supplied DC input cable into the Lind power adapter.
Is it normal for the adapter to get warm in use? Yes. Restricted air flow around the adapter
AC Voltage Specifications
DC power cord
90 - 264 volts AC
ˇ In the event of failure, contact a Lind service representative.
Connect output
Output
If the LED on the automobile power plug or the output LED on the adapter does not light
See adapter label
cable to device
*(See label on AC Adapter)
When using the Lind ruggedized combination AC/DC adapter, follow the precautions below.
to become very hot. The plastic cases of these splitters can entrap the heat and not allow it to
AC Input
+/-5% maximum
Call us with your needs.
Features
Replacement and direct input connection cables are available from Lind.
Replace only with same type and rating of fuse
5. Confirm that the green "Output Present" LED is on and that power is now being supplied
ˇ Never use a multi-plug adapter to plug multiple power plugs in the same outlet. If it is used, a
47-63 hertz (or 47 to 440 Hz)*
To connect the adapter to your system from an AC voltage source: (Reference: Figure 1)
DC power cord to adapter
-40ēC to +40ēC
3. Plug the AC power cord into the Lind power adapter.
31.3 ounces
connection may be wired directly to the appropriate fused DC source.
Input current
be a cigarette lighter connector, a Nato slave connector, a custom DC input connector or the
may even cause the adapter to overheat and shut down. This is a safety feature and does no harm
4. Insert the supplied DC input cable into the DC voltage source. The input cable options may
changed with a transformer or the like.
result.
**Operation below 0ēC may result in higher ripple voltage until adapter has warmed.
You can now use your system with the power supplied by the adapter.
Noted on adapter label
harmed.
See adapter label
have power at the lighter socket. It is also possible that one of the safety circuits in the adapter
ˇ When using the AC power input, use a power cord conforming to local safety standards.
normally shut down the adapter output but extreme voltage spikes may damage the adapter
Automatic Reset of Safety Cut-Offs
< [Pag.2]
Esta version es la html del arhivo pdf TECH_Ruggedized_Combo_AC_DC, genearada por domotica.name desde www.lindelectronics.com
Archivos relacionados:EVEREST LindProductO TECH_Adapter TECH_Airline TECH_AluminA TECH_LindLit TECH_Manual_ TECH_Manual_ TECH_Manual_ TECH_Manual_ TECH_Manual_ TECH_Manual_ TECH_Plastic TECH_Rugged_ TECH_Shut_Do TECH_Small_A TECH_Warrant audio acousticmagic acousticsfirst amina aperionaudio audiocontrol audioquest audioshare.net auralex bowers-wilkins bryston.ca caryaudio casatools cascadeaudio chillsound conextionsystems definitivetech eliteavdist furmansound lindelectronics martinlogan monitoraudiousa mseaudio nilesaudio noble-fidelity phasetech psaudio puristaudiodesign qsonix russound sheersoundcable sherbourn sonance ticcorp triadspeakers truaudio vdn-otl
