The high
Stat
www.jacksonsystems.com
Bedroom Area
proper terminals and are secure.
(nine if three panels are connected together). Each
continuous air circulation.
Zone dampers are powered closed and spring
Living Area
Indianapolis, IN 46203
Zone #1
Comfort SystemTM
dampers return to the open position to allow for
is in the open position.
When a green zone LED is on, that zone is calling
Panel
satisfied, the system will change over and take care
Zone #1 Damper
limit (HL-170) should be wired to the "HL"
System Checkout
Auto Changeover - Cooling Priority.
If any of the zone
damper terminals marked "DD" when the damper
stats can be either manual or auto changeover.
and another zone thermostat is calling for cooling,
To check the system for proper operation, pull the
return open. There will be no power at the panel
Zone Control
switches in heat mode and turn down all thermo-
E-mail:
Website:
not calling will have their dampers powered
5418 Elmwood Avenue
Turn the zone thermostat back down before check-
888.652.9663
of the heating requirement. This is referred to as
HVAC unit to have up to three separate zones
equipment will also be brought on at the same
the cooling thermostat will take priority and the
Toll-Free:
terminals on the zone control panel.
damper(s) remain open.
disconnect for the condensing unit to prevent short
info@jacksonsystems.com
a time, and call for heat to verify that the proper
for heating or cooling.
closed, and the zone(s) calling will have its (their)
Sequence Of Operation
Might Serve
heating or cooling equipment turns off and all zone
motorized zone damper.
the thermostat that is calling for cooling is
Z-300-HC Heat / Cool Zone Control Panel
thermostats call for heating or cooling, the zones
The low limit (FS-38) should be wired to the "LL"
The heating or cooling
system will operate in the cooling mode. When
terminals were removed before connecting the
Fax:
Comfort SystemTM is a residential / light commer-
cycling. Next, place all the zone thermostat mode
ing the next zone.
time. When all zone thermostats are satisfied, the
Might Serve
The zone control system works with standard,
Thermostats
single-stage, heat / cool thermostats. The thermo-
317.227.1034
Verify that all wires have been connected to the
zone is controlled by its own space thermostat and
11-17-03
stat set points. Go to each zone thermostat, one at
Transformer
24 Volt 40VA
terminals on the zone control panel.
Verify that the jumpers across the "LL" and "HL"
cial zone control system that allows a single
Zone #2
Stat
If one of the zone thermostats is calling for heating
Typical System
Zone #2 Damper
zone dampers are open (and the rest are closed).
high and low limit stats.
< [Pag.2]
Esta version es la html del arhivo pdf z300_hc_install_sheet, genearada por domotica.name desde www.jacksonsystems.com
Archivos relacionados:Catalog-004 GreenRibbon Green_HO_she RSESarticle SL-2000logo Z-200-HC-IOS Z-200-HP-IOS Z-2000end Z2000-Round- Z2000book ZDRect aprilaire_au aprilaire_hu bd_series_ba bypassdamper certificate concealstatf creditapp d_series_rec d_series_rou ductworksizi energy_savin fact_sheet homeownerbot patch retrodamper stats_on_sta tempstatfaq trimed_uvlam vav wr_1F78_144 wr_1F85_277 wr_1F93_380 wr_bluetouch z200HP z200saleslit z300_hc_ms_i z300_homeown z300_hps_dat z600saleslit zone_one zone_one_dat zone_one_mod seguridad cctvsafe extremecctv freezealarm goodbarsecurity highpowersecurity icontrol infosecinstitute intamac jacksonsystems keepsafer mraccess napcosecurity nexusaudiosystems securityandmore securitymaninc smartvue techno-mall tripplite vigitron vikingelectronics wilife
