DAS
during the occupied mode. Wire 24 volts to the time clock using terminals
5418 Elmwood Avenue, Indianapolis, IN 46203-6025
Z-2000 COMFORT SYSTEMTM
TT
,
24 VAC INPUT POWER
minutes. Time delay speed up should only be used for start up and service.
recommended.
from each zone damper to the terminals labeled
three zones have to call to bring on the equipment. If both
temperature control and override during unoccupied periods. 18-2 thermostat wire is recommended.
3 ZONES
Zone Control Made SimpleTM
The control panel is equipped with a time delay speed up button. When the speed up button is engaged the time delays
selector switches located on the interface board. When both
MINIMUM CALLS SELECTION SWITCHES
switches are in the OFF position, any zone calling can bring on the equipment. When the
recommended.
and
NS
on the interface board. 18-8 thermostat wire is
Install the Z-2000 Comfort SystemTM control panel on a flat surface near the HVAC equipment. The panel should be
WR C, Y
DISCHARGEAIR TEMPERATURE SENSOR
position, at least two zones have to call to bring on the equipment. When the
The control panel requires a heating and cooling contact closure from each zone damper. Connect terminals
Minimum Calls
2 ZONES
24 VOLT POWER
rooftop unit.
The control panel is wired to the HVAC equipment in the same way as a standard 2-stage heat / 2-stage cool thermostat.
the supply duct. Connect the sensor to the terminals labeled
normally open night stat and override timer can be wired in parallel to terminals
HVAC UNIT
switch is in the ON position, at least
switches are in the ON position, the
The control panel has an optional input for a time clock, night stat, and override timer. To install a time clock, remove the
located above the
factory installed jumper between the two terminals labeled
GENERAL NOTES
The control panel requires a 24 Volt transformer with a proper VA rating.
recommended.
2 ZONES
board. 18-2 thermostat wire is recommended.
The control panel requires a discharge air temperature sensor. Mount the sensor 26 inches from the HVAC equipment in
TT
AND . Wire the time clock using the contacts that are closed
W
terminals. A
between stages and between modes of operation are divided by 15. The time delay speed up mode will reset after fifteen
TIME CLOCK, NIGHT STATAND OVERRIDE TIMER (OPTIONAL)
RC
Do not power the control panel from the
to provide unoccupied
RCY
on the interface board. 18-2 thermostat wire is
NS
,
08-1030-060707
3 ZONES
Do not install the control panel on or inside a
, , and
The control panel is equipped with two
on the interface board. 18-4 thermostat wire is
Connect the HVAC equipment to the terminals labeled
and
switch is in the ON
and
HVAC SYSTEM
transformer in the HVAC equipment.
TIME DELAY SPEED UP BUTTON
default is three.
R, C, Y,AND W ZONE DAMPER TERMINALS
on the interface
installed in a dry, clean location approximately 60 inches from the floor.
www.jacksonsystems.com
Connect 24 Volts to the terminals labeled
WIRING DETAILS
, and
Toll Free: 888.652.9663 Fax: 317.227.1034
and
<< < [Pag.9] > >>
Esta version es la html del arhivo pdf Z2000book, genearada por domotica.name desde www.jacksonsystems.com
Archivos relacionados:Catalog-004 GreenRibbon Green_HO_she RSESarticle SL-2000logo Z-200-HC-IOS Z-200-HP-IOS Z-2000end Z2000-Round- ZDRect aprilaire_au aprilaire_hu bd_series_ba bypassdamper certificate concealstatf creditapp d_series_rec d_series_rou ductworksizi energy_savin fact_sheet homeownerbot patch retrodamper stats_on_sta tempstatfaq trimed_uvlam vav wr_1F78_144 wr_1F85_277 wr_1F93_380 wr_bluetouch z200HP z200saleslit z300_hc_inst z300_hc_ms_i z300_homeown z300_hps_dat z600saleslit zone_one zone_one_dat zone_one_mod seguridad cctvsafe extremecctv freezealarm goodbarsecurity highpowersecurity icontrol infosecinstitute intamac jacksonsystems keepsafer mraccess napcosecurity nexusaudiosystems securityandmore securitymaninc smartvue techno-mall tripplite vigitron vikingelectronics wilife
