located on the panel is set properly.
may not energize immediately due to thermostat or panel
INDOOR
H
1. Verify that all component wires have been connected to
Z NE
MIGHT SERVE
8. Determine the ventilation mode of each zone thermostat
SENSOR
H
Operating Humidity:
and that the (Y) and (G) LEDs are ON. Note: Equipment
D
Programmable or non-programmable
TRANSFORMER
6. Put zone #1 thermostat in the cooling mode and have
06-1033-050508
24Vac (Hot)
W
6.0 Inches
have its damper open and there will be no 24Vac on the `D'
Z-200-HP Installation and Operation Instructions
W
Reversing Valve
Operating Temperature Rating:
T
LIVING AREA
Discharge Air Sensor (2 wire)
#2 `D' and `D' terminals.
O/B
Z-200-HP
Auxiliary Heat
G
STAT
E
1.375 Inches
E
System Checkout:
Fan
7. Turn zone #1 thermostat off and repeat steps 5 and 6
First Stage Compressor
HIGH/LOW
3 minutes minimum off between calls
Panel Power:
24Vac (Hot)
9. Reconnect the HVAC `R' wire at the panel.
with zone #2 thermostat. Remember, the zone calling will
24Vac (Common)
by setting the thermostats in the Fan Auto or ON mode.
5. Put zone #1 thermostat in the heating mode and have
Thermostats:
Mounting:
is energized. Make sure the reversing valve slide switch
Specifications:
O/B
voltage on zone #1 `D' and `D' terminals and 24Vac on zone
Dampers:
LIMIT
24Vac (Common)
1. Disconnect the HVAC `R' terminal wire at the panel and
-40° F to 150° F
G
ZONE DAMPER 1
18-gauge wire for all equipment
the thermostat call for heat. Confirm that (ZD1) LED is ON
Thermostats:
E
www.jacksonsystems.com
Power Closed / Spring Open (2 wire)
R
PANEL
open and zone #2 damper is closed. There will be no
3 minutes minimum off on low limit
Toll Free: 888.652.9663 Fax: 317.227.1034
HEAT PUMP
Zone Control Made SimpleTM
4. Place both zone thermostats in the OFF position.
5% to 90% RH non-condensing
3. Confirm that the LIMIT LED is ON.
First Stage Compressor
BEDROOM AREA
STAT
2 Heat / 1 Cool Heat Pump - Auto Changeover - First Call Priority
Y
time delays.
and system connections.
the thermostat call for cool. Confirm that (ZD1) LED is ON
and `D' terminals for that zone.
Width:
DAS
Reversing Valve
N
Depth:
Height: 8.0 Inches
X
Fan
the proper terminals and are secure.
HVAC Equipment:
R
Auxiliary Heat
24Vac (Hot)
Typical System Layout
G
5418 Elmwood Avenue, Indianapolis, IN 46203-6025
Heat pump thermostats
Zone Control Made SimpleTM
24 VOLT 40VA
20 minute time share
C
The (O/B) LED is ON when the reversing valve
UNIT
Wiring:
TM
Snap Track with 2 back plate screws
ZONE DAMPER 2
MIGHT SERVE
Auto or manual changeover
and that (Y) LED is ON. Confirm that zone #1 damper is
R
Terminal Designations:
Panel Dimensions:
ZONE 1
Y
Time Delays:
High / Low Limit
apply 24Vac to the panel.
ZONE 2
< [Pag.2]
Esta version es la html del arhivo pdf Z-200-HP-IOS-Manual, genearada por domotica.name desde www.jacksonsystems.com
Archivos relacionados:Catalog-004 GreenRibbon Green_HO_she RSESarticle SL-2000logo Z-200-HC-IOS Z-2000end Z2000-Round- Z2000book ZDRect aprilaire_au aprilaire_hu bd_series_ba bypassdamper certificate concealstatf creditapp d_series_rec d_series_rou ductworksizi energy_savin fact_sheet homeownerbot patch retrodamper stats_on_sta tempstatfaq trimed_uvlam vav wr_1F78_144 wr_1F85_277 wr_1F93_380 wr_bluetouch z200HP z200saleslit z300_hc_inst z300_hc_ms_i z300_homeown z300_hps_dat z600saleslit zone_one zone_one_dat zone_one_mod seguridad cctvsafe extremecctv freezealarm goodbarsecurity highpowersecurity icontrol infosecinstitute intamac jacksonsystems keepsafer mraccess napcosecurity nexusaudiosystems securityandmore securitymaninc smartvue techno-mall tripplite vigitron vikingelectronics wilife
