cover. This completes the internal wiring of the
the unit was in the middle of sequencing on and had
with outlet A, then B, etc. until all outlets are on. if the
cable to the ASD-120 and terminate it with Cam-lok,
seconds, regardless of the setting of the internal delay
The ASD-120's control circuits turn on the outlets
in order from A to f when sequencing on, and turn
cable termination is to break the ends out as pig-
The quick start section at the front of the manual is adequate for
"J" Custom Supply, telephone 1-800-226-5657 (1-
Sequence:
adjustable with a trim pot, with a range of 0.2 to > 12
has been changed from the factory-preset Maintained
ASD-120's rear panel terminal strip. In addition, the
Remote Control: in the REM position, an on or
for each individual conductor.
ReM) position initiates an on sequence. Please note
by its corresponding front panel ON/SeQ/Off toggle
seconds per step. (Total time for the entire sequence is
7. Set internal jumpers to suit your application: See
mentioned in item 2 (on page 6), the most common
cable with mating Cam-loks would then be prepared
setting is approximately 8 seconds per step.
rear panel remote inputs will again control the unit.
purely local control, you should leave the mode set to
Operating Modes.
typical use. The following is an advanced tutorial and description
controLLing
ASD-120 will stay on if all outlets are already on, or, if
rear panel remote control inputs. if the key switch is later
currently off will go on, so the sequence reverses
seconds, regardless of the setting of the delay time
ASD-120 SequenceD Power DiStro
one good way is to permanently attach a very short
if you want to provide a way to disconnect the cable
8
with outlet f, then E, etc. until all outlets are off. if
mode, also by the START ON/Off SeQUeNCe
trimpot. The next and all following outlets turn on at
that in the absence of any signal applied to the remote
each venue. in some circumstances, a suitable con-
Mode to Momentary Mode, you must also press the
ADVAnceD
from 1 second to > 1 minute).
When the unit is turned off with the key switch, the
Table 4 on page 9.
maintained or momentary switch connected to the
not yet turned on all outlets, the highest outlet that
panel key switch, or remotely, via a remotely located
nector may be provided at the power source and the
described in the preceding section on local control.
ASD-120's sequencing circuits will not respond to the
Maintained.)
connected to the rear panel inputs, or, in Momentary
off sequence is initiated by one or more switches
When the unit is turned on with the key switch, the
for those who are so inclined.
ASD-120.
behavior of any individual circuit may be overridden
without ever activating the outlets that had not yet
6. Terminate source end of cable or wire bundle: As
START ON/Off SeQUeNCe button. However, for
the outlets off in the reverse order from f to A when
When the key is in either the On or Off position, the
unit was in the middle of sequencing off and had not
turned on. The highest on outlet turns off within 0.2
tails and leave its hookup to the house electrician in
which could easily be disconnected and stored. A
time trimpot. The next and all following outlets turn off
from the ASD-120 for separate storage or shipment,
local control: Turning the key to the On (or possibly
without ever deactivating the outlets that had not
cable can be terminated with a mating connector.
yet turned off all outlets, the lowest outlet that was
Meltric, or similar high-current connectors. A long
yet gone off. The lowest off outlet turns on within 0.2
sequencing off. The time for each step is internally
Often these will be Cam-lok® or similar connectors
returned to the REM position, the signals supplied to the
good source for custom made high power cables is
input, the REM position defaults to on. (if the ASD-120
on/oFF
button. The ASD-120 responds exactly as it does as
at intervals controlled by the trimpot.
is currently on will go off, so the sequence reverses
initiated in either of two ways: locally, via the front
800-CAM-lOKS).
See the next section for a discussion of Remote
ASD-120 will stay off if all outlets are already off, or, if
all outlets are off, will begin turning on outlets starting
switch.
A normal, time-delayed on or off sequence may be
all outlets are on, will begin turning off outlets starting
intervals controlled by the trimpot. The factory default
<< < [Pag.9] > >>
Esta version es la html del arhivo pdf ASD-120_manual, genearada por domotica.name desde www.furmansound.com
Archivos relacionados:AC-215_datas ACD-100_data ACD-100_manu AR-1215_AR-2 AR-1215_manu AR-1230_data AR-15_datash AR-15_manual AR-20_datash AR-PRO_datas AR-PRO_manua ASD-120_data Furman_Merit Furman_Merit HDS-16_HRM-1 HDS-6_HR-6_d HDS-6_HR-6_m HR-2_manual IT-1210_IT-1 IT-1230_manu IT-20_II_dat MERIT_SERIES MERIT_SERIES PL-8_PL-PLUS PL-8_PL-PLUS POWER_FACTOR POWER_FACTOR POWER_LINK_d POWER_STATIO PS-8R_II_dat PS-8R_II_man PS-8_PS-8R_P PS-8_PS-8R_d PS-PRO_II_ma PST-6_manual PST-8_D_manu RACKRIDER_PW RL-I_RL-LED_ RS-1_RS-2_ma SERIES_II_15 SERIES_II_15 SERIES_II_20 SERIES_II_20 SP-20A_datas SPB-8C_datas SPB-8C_manua SPB-8_datash SPB-8_manual audio acousticmagic acousticsfirst amina aperionaudio audiocontrol audioquest audioshare.net auralex bowers-wilkins bryston.ca caryaudio casatools cascadeaudio chillsound conextionsystems definitivetech eliteavdist furmansound lindelectronics martinlogan monitoraudiousa mseaudio nilesaudio noble-fidelity phasetech psaudio puristaudiodesign qsonix russound sheersoundcable sherbourn sonance ticcorp triadspeakers truaudio vdn-otl
