may cause the air relief port on the top of the skimmer body to leak water.
Begin disassembling Fastlane Pool by taking of all of the corners.
Unhook the hydraulic hose connections at the Fastlane Mounting Bracket and cap all
800-910-2714.
Be very careful to slowly and carefully pull the corners from the top rails.
Remove the Fastlane Swim Unit rails from the Mounting Bracket and detach the
winter weather occurs.
The Fastlane Pool requires no special preparation for the off-season. They are
Once the pool is drained, reach in each corner pocket and pull the liner away from
Once the liner is loose from the top rail, walk around the outside perimeter of the
Store your pool and Fastlane Swim Unit in a dry safe place.
Once corners are off, lift top rails off of the legs and disassemble the remainder of
corner of the liner.
If you have any questions, please contact our Customer Service Department at 1-
Swim Unit and view ports.
Weekly
If you only close the pool, know that "Winterizing" is specific to the climate the pool
Winterizing the Fastlane Pool
Fastlane Mounting Bracket. Pull Fastlane Swim Unit out of the pool carefully so as
honeycomb grill where the current is produced. Water 1/2" lower than this
"Winterizing" generally refers to the treatment of the water in the pool, draining
Take the Fastlane Pool down and/or re-install indoors if in an area where harsh
honeycomb grill will cause more water to get splashed out of the pool, and
the fluid inside will not freeze.
plumbing lines. Having the water level 1" or more higher than that
Test the pH level at least twice a week. Broadcast (i.e. pour chemical into the
5/22/08
can create a choppy current and may cause your skimmer to draw air into the
treated the same as any other aboveground pool.
The hydraulic run hoses will need to be capped off to prevent the fluid from draining
below the Fastlane Swim Unit and draining your equipment, again the pool itself
When storing your pool, thoroughly clean and dry the liner and carefully roll it up.
ends to prevent hydraulic fluid from draining.
Check and adjust the water level. The water should completely cover the
Always store the hard parts and the liner in separate boxes.
the top rail tubes.
current) pH increaser or pH decreaser to maintain levels between 7.4 and 7.8.
pool moving the wall back and forth to loosen the top rail and corner joints.
out.
not to damage the pool liner. Remove PVC Support Base.
If you do choose to winterize, you must drain the Fastlane Pool below all wall fittings,
FLPoolOMDMver1.2
the pool. Make sure the liner is rinsed and fully dry before storing.
Page 20 of 23
requires no special attention.
Disassembling the Fastlane Pool
The hydraulic Power Unit can remain outside as well at the hydraulic run hoses as
is located in.
Jolting or forcing the corner out of the top rail can create a tear in the
<< < [Pag.20] > >>
Esta version es la html del arhivo pdf FLPoolOMDMver, genearada por domotica.name desde www.endlesspools.com
Archivos relacionados:ARSC Assemblyinst EPSSOpGuidev FAQ FLPoolOMWMWQ FLPoolOMWMWQ FL_Brochure FOP012309 FastlaneOMv4 FastlanePool FastlaneWarr Fastlane_Pla IntroBook PDFConfigsAG PDFConfigsFI PDFConfigsFI PDFConfigsPI PDFConfigsPI Permit_Consi SwimSpaBroch SwimSpaPlann USBRENDLESSP coastallivin eheater epiwarranty finishchoice gheater howtoswim options planningguid wallmountOM motores activateddecor aquaair-wetdry auton avrak closystems endlesspools hpproducts.net innovativepools mediadecor peerlessmounts plasma-tv-lift silentgliss-usa somfysystems watercop
