(for battery connection) and a quick-release connector.
release connector. Attach the power supply quick-release connector to the vehicle quick-
DC Output Terminals
Before making any connections, be sure that the AC cord of your APS Power Supply is unplugged.
·
The vehicle battery ground cable should also be disconnected before working on the positive battery terminal.
·
supply can be quickly attached or removed by utilizing the two quick realease connectors.
release connector by snapping them together. They will only go together one way.
The second half of the supplied cable assembly will be attached to your APS power supply. This will allow the power supply
Important Note:
Included in the kit are two cable assemblies. The first assembly will be connected to the vehicle battery.
wire strands are in the block (no fliers). Tighten the terminal
022004-LO-R1
Loosen the nut and bolt attaching the ground (-) cable of the vehicle to the battery. Remove the nut and attach the black
One half of the cable assembly will be connected to the vehicle battery terminals. The other half of the cable assembly is to
sales@cascadeaudio.com
Route the cable to a spot where it is easy to reach the quick-release connector. Mount the connector to the desired location
An error here can cause damage and/or injury.
Place the APS Power Supply under the vehicle. Locate the vehicle mounted quick-
the negative battery post and tighten the bolt.
charging the battery.
1 pc. - 4 ft. cable assembly consisting of 4 ga. pos. and neg. cables and a pre-terminated quick-release connector.
Kit Contents:
Connecting The Supply To The Vehicle
in the engine compartment (or behind the bumper) using tie wraps or permanently fasten the connector using sheet metal
The APS Four Gauge Cable Kit provides all of the critical components necessary for installation of any APS Power Supply.
Plug the A/C power cord from your APS unit into the wall outlet. The power supply is now
Carefully insert the stripped end of the black cable into the NEG terminal connection of the block making sure that all of the
APS-HK4
Carefully insert the stripped end of the red cable into the POS terminal connection of the block making sure that all of the
www.cascadeaudio.com
The second assembly will be connected to your APS power supply. Once the kit is installed into a vehicle, the APS power
·
·
It features a unique "quick-release" connector allowing it to be quickly and easily plugged or unplugged from any vehicle.
to be quickly connected to, or removed from, the vehicles' battery.
PH: 541-389-6821 - FX: 541-389-5273
·
Installation:
Locate the screw terminals on the output end of the APS Power Supply labeled POS (Positive) and NEG (Negative).
cable to the bolt of the vehicle battery cable using the ring connector. Re-attach the nut (hand tight). Mount the terminal to
Loosen the screws located on the top of the terminal block.
screws or nuts and bolts through the holes provided in the connector.
·
·
wire strands are in the block (no fliers). Tighten the terminal.
·
ring connector. Re-attach the nut and tighten the bolt.
Locate the cable assembly with the attached 3/8" ring connectors. Loosen the nut and bolt holding the Positive (+) cable of
·
On the second half of the supplied cable assembly. Strip approx. 1/2" of insulation from the end of the red and black cables.
·
Proper polarity of the cables at the connector is automatically ensured. They only fit together correctly.
·
be attached to the APS power supply. BE SURE TO OBSERVE PROPER POLARITY (Plus to Plus and Minus to Minus!)
Battery Cable Installation
the vehicle to the battery. Remove the nut and attach the red cable to the bolt of the vehicle battery cable using the
1 pc. - 4 ft. cable assembly consisting of 4 ga. pos. and neg. cables, pre-terminated with 3/8" ring terminals
4 GAUGE QUICK REALEASE CABLE KIT
[Pag.1]
Esta version es la html del arhivo pdf HK-4Install, genearada por domotica.name desde www.cascadeaudio.com
Archivos relacionados:APS-15_mount APS-55_220V_ APSSpecsOnly APS_Checklis APS_Manual APS_Specs_20 APS_Technica AcousticCott CAE_Windows CAP_Instruct Deflex_Tech ECCOBOX_TECH Fab-Trax_Dat FabTraxTech Hardwood_iso Insulator_In Insulator_Te IsoTileTech Phonic RSIC_1Tech SB-Barricade SB-TileAD_te SB-WBDTech SG-1_Instruc SG-1_Tech Soundproof_D TG-1_Install TG-1_Tech TGT1_tech VB-1S_Pro_Te VB-1X_Instal VB-1X_Tech VB-2MAX_Tech VB-2_2HD_Ins VB-2_VB-2HD_ VB-4_Install VB-5_Install VB-5_Tech VB-TS_Instal VB-TS_Tech VMAX_Install VMAX_Tech aps_faq cae_window_i audio acousticmagic acousticsfirst amina aperionaudio audiocontrol audioquest audioshare.net auralex bowers-wilkins bryston.ca caryaudio casatools cascadeaudio chillsound conextionsystems definitivetech eliteavdist furmansound lindelectronics martinlogan monitoraudiousa mseaudio nilesaudio noble-fidelity phasetech psaudio puristaudiodesign qsonix russound sheersoundcable sherbourn sonance ticcorp triadspeakers truaudio vdn-otl
