unplug the blocks and connect all of the speaker wires
remote power switching, you can plug the unit into an
inputs.
Installer's Guide
Thru Outputs - These unbalanced RCA outputs
Ground Lift Switch - This switch selects the level of
Speaker Outputs - These terminal blocks are
11
Remote Power Control - This three pin connec-
500 watts at full power. Make certain that it is
Î
outlet that is always active.
Ó
wrong.
after an audio signal is present on the Input RCA
Inputs - These unbalanced RCA inputs connect
Í
octave slope and the filter frequency is adjustable
switch in to the recessed (Defeat) position.
isolation between the audio signal ground and your
Ó
ment controls the input sensitivity of the Architect
Ï
going to be shut down for an extended period of time.
11
AC Power Fuse - The Architect is designed with
Model 100 & Model 200
level audio signal can be connected to these
is here just in case something really awful goes
11
jacks. To defeat this function and leave the
5
Master Power Switch - This switch shuts off the
11
11
for installers that prefer this type of speaker connec-
from 20Hz to 80Hz.
Î
Ï
to your preamplifier's outputs. Any standard line
amplifier. The sensitivity is variable from 0-1
AC earth ground. In normal operation this switch
PFM Highpass Filter - This bass blocking filter
Rear Panel
11
settings for the best operation. For your safety, the
A Guided Tour Of
tion (The Architect Model 105 and Model 205).
speaker connector blocks will accept up to 12 awg
multiple amplifiers together.
Ì
power other pieces of equipment. It is a current
ÐÒ
cuitry activates a zone approximately 0.5 second
limited output for switching the Architect only.
several layers of protection circuitry. This power fuse
the Architect. The PFM features an 18dB per
Ñ
An optional set of 5-way binding posts are available
Control In and the +12V output or an external 12
regardless of the switch setting.
Ê
turn the master power switch off is if the system is
Ë
Ñ
11
11
without ever taking the Architect out to the installa-
ÊËÌÍ
tor allows you to remotely turn on the Architect.
Ð
simplify connection to multiple speaker zones. The
Ò
11
main AC power. Normally the only time you need to
You can either use a contact closure between the
should be in the Ground position, but if you run into
send a buffered audio output to daisy-chain
11
volt.
tm draws approximately
The Architect
with sufficient power rating. Since the Architect has
to them without balancing the Architect on your lap.
plugged directly into the wall outlet or a power strip
The Architect
adjustment sets the low frequency cut-off point of
Input Level Control - This screwdriver adjust-
trouble with an AC ground hum, try the other two
tion site. The two output blocks are paralleled to
This also makes it very simple to pre-wire a system
terminals. The +12 volt output is not designed to
designed to make an installer smile. You can
Architect ready to play at all times, press this
volt trigger between the Control In and Ground
chassis is always connected to the earth ground
Power Cord - The Architect
tm Model 100 & Model 200
wire.
Signal Sense Defeat - The signal sensing cir-
<< < [Pag.9] > >>
Esta version es la html del arhivo pdf 355, genearada por domotica.name desde www.audiocontrol.com
Archivos relacionados:0408Pro52620 0506Pro52620 AllAboutCros EQS_Lit EXPO_2005_Pr EXPO_2006_Me ME1105p75-83 TwoRoomsHT07 au-bv au-bvlit epicenter_OM firmaliste weinberg109 audio acousticmagic acousticsfirst amina aperionaudio audiocontrol audioquest audioshare.net auralex bowers-wilkins bryston.ca caryaudio casatools cascadeaudio chillsound conextionsystems definitivetech eliteavdist furmansound lindelectronics martinlogan monitoraudiousa mseaudio nilesaudio noble-fidelity phasetech psaudio puristaudiodesign qsonix russound sheersoundcable sherbourn sonance ticcorp triadspeakers truaudio vdn-otl
